B5 Models Please discuss all 1996 - 2001 B5 A4 topics here...

aledelic42's timeline.

Thread Tools
 
Search this Thread
 
  #831  
Old 12-20-2010, 11:04 AM
tware4021's Avatar
1st Gear
Join Date: May 2009
Location: Syracuse New York
Posts: 468
Default

damn! too bad they are coming in tomorrow or i would have canceled the order and ordered the set! God i hate being retard!
 
  #832  
Old 12-20-2010, 01:03 PM
aledelic42's Avatar
3rd Gear
Thread Starter
Join Date: Jan 2008
Location: Bethlehem, PA
Posts: 2,058
Default

I think the car looks extra high in that picture because of the shadows on the fenders. the a4 mud flaps on ecs are only rears. I bought both different pairs while one was labeled fronts and have four pairs of rear flaps the s4 set fits fine. the fronts may look a little off without s4 skirts/molding though and they will definitely touch the ground with only a few inches lower.. not sure what I'll do about that, either trim or drag. I bought three sets
 
  #833  
Old 12-23-2010, 04:58 PM
aledelic42's Avatar
3rd Gear
Thread Starter
Join Date: Jan 2008
Location: Bethlehem, PA
Posts: 2,058
Default

anyone have good ideas for the shortest ways to route air line from the center console to each corner's bag?
 
  #834  
Old 12-23-2010, 08:09 PM
kriptonik's Avatar
Administrator
Join Date: Oct 2006
Location: Los Angeles, CA
Posts: 11,291
Default

My buddy with an MK5 GLI ran the fronts through the door sills and the rears through the spare wheel well.
 
  #835  
Old 12-23-2010, 09:26 PM
kayakman13's Avatar
2nd Gear
Join Date: Feb 2009
Location: Oregon
Posts: 1,301
Default

Very excite!
 
  #836  
Old 12-24-2010, 01:51 AM
aledelic42's Avatar
3rd Gear
Thread Starter
Join Date: Jan 2008
Location: Bethlehem, PA
Posts: 2,058
Default

I would run them like that but I have paddle valves in the center of the car instead of electric valves in the back.. I think I might just have the fronts come out by the door hinges with the other wires going into the doors... not sure about the rears but I'll probably just find a spot to drill a hole in the wheel well.. I'm hating the manual paddle valves so far
 
  #837  
Old 01-02-2011, 02:14 AM
NickBroderick's Avatar
3rd Gear
Join Date: Apr 2009
Location: Mansfield, MA
Posts: 2,617
Default

Ready. Set. Go.
 
  #838  
Old 01-02-2011, 06:54 PM
aledelic42's Avatar
3rd Gear
Thread Starter
Join Date: Jan 2008
Location: Bethlehem, PA
Posts: 2,058
Default

 
  #839  
Old 01-02-2011, 06:55 PM
kayakman13's Avatar
2nd Gear
Join Date: Feb 2009
Location: Oregon
Posts: 1,301
Default

I'm very interested in that picture! Looks like your front is ready to scrape... or am I just fooling myself?
 
  #840  
Old 01-02-2011, 07:12 PM
aledelic42's Avatar
3rd Gear
Thread Starter
Join Date: Jan 2008
Location: Bethlehem, PA
Posts: 2,058
Default

only the fronts are in. it goes pretty low but I would really like it to be lower. it's around 22.75 ground to fender, I have to figure out what's holding them up. I'll probably look at it tomorrow and also start a new thread soon

blurry picture
 

Last edited by aledelic42; 01-02-2011 at 07:24 PM.


Quick Reply: aledelic42's timeline.



All times are GMT -4. The time now is 02:41 PM.